Resiliency

Dell Container Storage Modules (CSM) for Resiliency installation

CSM for Resiliency is installed as part of the Dell CSI driver installation.

For information on the PowerFlex CSI driver, see PowerFlex CSI Driver.

For information on the Unity XT CSI driver, see Unity XT CSI Driver.

For information on the PowerScale CSI driver, see PowerScale CSI Driver.

For information on the PowerStore CSI driver, see PowerStore CSI Driver.

For information on the PowerStore CSI driver, see PowerMax CSI Driver.

Configure all the helm chart parameters described below before installing the drivers.

Helm Chart Installation

The drivers that support Helm chart installation allow CSM for Resiliency to be optionally installed by variables in the chart. There is a podmon block specified in the values.yaml file of the chart that will look similar to the text below by default:

# Enable this feature only after contact support for additional information
podmon:
  enabled: true
  controller:
    args:
      - "--csisock=unix:/var/run/csi/csi.sock"
      - "--labelvalue=csi-vxflexos"
      - "--mode=controller"
      - "--skipArrayConnectionValidation=false"
      - "--driver-config-params=/vxflexos-config-params/driver-config-params.yaml"
      - "--driverPodLabelValue=dell-storage"
      - "--ignoreVolumelessPods=false"
  node:
    args:
      - "--csisock=unix:/var/lib/kubelet/plugins/vxflexos.emc.dell.com/csi_sock"
      - "--labelvalue=csi-vxflexos"
      - "--mode=node"
      - "--leaderelection=false"
      - "--driver-config-params=/vxflexos-config-params/driver-config-params.yaml"
      - "--driverPodLabelValue=dell-storage"
      - "--ignoreVolumelessPods=false"

To install CSM for Resiliency with the driver, the following changes are required:

Enable CSM for Resiliency by changing the podmon.enabled boolean to true. This will enable both controller-podmon and node-podmon.
If you need to change the registry, specify the podmon image to be used in images.podmon
Specify arguments to controller-podmon in the podmon.controller.args block. See “Podmon Arguments” below. Note that some arguments are required. Note that the arguments supplied to controller-podmon are different from those supplied to node-podmon.
Specify arguments to node-podmon in the podmon.node.args block. See “Podmon Arguments” below. Note that some arguments are required. Note that the arguments supplied to controller-podmon are different from those supplied to node-podmon.

Podmon Arguments

Argument	Required	Description	Applicability
enabled	Required	Boolean “true” enables CSM for Resiliency installation with the driver in a helm installation.	top level
mode	Required	Must be set to “controller” for controller-podmon and “node” for node-podmon.	controller & node
csisock	Required	This should be left as set in the helm template for the driver. For controller: `-csisock=unix:/var/run/csi/csi.sock` For node it will vary depending on the driver’s identity: `-csisock=unix:/var/lib/kubelet/plugins` `/vxflexos.emc.dell.com/csi_sock`	controller & node
leaderelection	Required	Boolean value that should be set true for controller and false for node. The default value is true.	controller & node
skipArrayConnectionValidation	Optional	Boolean value that if set to true will cause controllerPodCleanup to skip the validation that no I/O is ongoing before cleaning up the pod. If set to true will cause controllerPodCleanup on K8S Control Plane failure (kubelet service down).	controller
labelKey	Optional	String value that sets the label key used to denote pods to be monitored by CSM for Resiliency. It will make life easier if this key is the same for all driver types, and drivers are differentiated by different labelValues (see below). If the label keys are the same across all drivers you can do `kubectl get pods -A -l labelKey` to find all the CSM for Resiliency protected pods. labelKey defaults to “podmon.dellemc.com/driver”.	controller & node
labelValue	Required	String that sets the value that denotes pods to be monitored by CSM for Resiliency. This must be specific for each driver. Defaults to “csi-vxflexos” for CSI Driver for Dell PowerFlex and “csi-unity” for CSI Driver for Dell Unity XT	controller & node
arrayConnectivityPollRate	Optional	The minimum polling rate in seconds to determine if the array has connectivity to a node. Should not be set to less than 5 seconds. See the specific section for each array type for additional guidance.	controller & node
arrayConnectivityConnectionLossThreshold	Optional	Gives the number of failed connection polls that will be deemed to indicate array connectivity loss. Should not be set to less than 3. See the specific section for each array type for additional guidance.	controller
driver-config-params	Required	String that set the path to a file containing configuration parameter(for instance, Log levels) for a driver.	controller & node
ignoreVolumelessPods	Optional	Boolean value that if set to true will enable CSM for Resiliency to ignore pods without persistent volume attached to the pod.	controller & node

PowerFlex Specific Recommendations

PowerFlex supports a very robust array connection validation mechanism that can detect changes in connectivity in about two seconds and can detect whether I/O has occurred over a five-second sample. For that reason it is recommended to set “skipArrayConnectionValidation=false” (which is the default) and to set “arrayConnectivityPollRate=5” (5 seconds) and “arrayConnectivityConnectionLossThreshold=3” to 3 or more.